Durodent Model Seal Separating Solution 1L
- Brand: Durodent
- Product Code: DMS-1
Durodent Model Seal Separating Solution
IMROVED FORMULA - Increased stability
Separating solution is painted on to form a separating barrier between the plaster and acrylic in the flask. Sodium Alginate based separating solution works by a chemical reaction to the stone.
Correct Application Procedure: Hot Model Seal
- Completely remove wax residue, grease and dirt from the plaster model and plaster surfaces to be separated.
- Then on a hot-warm dry model apply a liberal coat of separator with a clean soft brush.
- Immediately after carefully rinse off any excess separating solution under running water and allow the model to drain and air dry until a satin gloss finish has formed on the surface
- If applying a second coat, this must be done before the first coat dries.
- Wash the used brush and dispose of the remaining separating agent.
Tip: If it is flaking or peeling, material has been applied to thick or not removed before it has dried.
Applications:
- Gypsum to acrylic
- Gypsum to composite
- On all gypsum materials
- For heat curing and self (cold) curing acrylics
Important information:
- Applying on a hot model accelerates infiltration and drying of the separating agent.
- If applying a second coat the first layer of separating agent should not be completely dried before the second layer is applied. If so, this can result in white discolouration on the acrylic surface. The second coat should only be a light application and be rinsed liked the first coat.
- Never empty remaining separating agent back into the original container or immerse the used brush in the bottle. This results in contamination and consequently degradation of the separating solution.
DO NOT STORE IN DIRECT SUNLIGHT OR HOT AREA
Must be stored at no more than 25° in dark area (Heat Sensitive). Product may lose red colour due to light.
Use with in 6 months
**** Please be aware Separating Solutions are affected by heat exposure or UV exposure which will cause them to loose their properties. Product must be stored in a cool dark place and should be decantered into small bottle to use in the working area. If the solution has gone watery (no longer slimy or slightly thick) then it will no longer work as the natural alginate material has broken down due to elements.
Durodent Model Seal Separating Solution 1L
- Brand: Durodent
- Product Code: DMS-1
Durodent Model Seal Separating Solution
IMROVED FORMULA - Increased stability
Separating solution is painted on to form a separating barrier between the plaster and acrylic in the flask. Sodium Alginate based separating solution works by a chemical reaction to the stone.
Correct Application Procedure: Hot Model Seal
- Completely remove wax residue, grease and dirt from the plaster model and plaster surfaces to be separated.
- Then on a hot-warm dry model apply a liberal coat of separator with a clean soft brush.
- Immediately after carefully rinse off any excess separating solution under running water and allow the model to drain and air dry until a satin gloss finish has formed on the surface
- If applying a second coat, this must be done before the first coat dries.
- Wash the used brush and dispose of the remaining separating agent.
Tip: If it is flaking or peeling, material has been applied to thick or not removed before it has dried.
Applications:
- Gypsum to acrylic
- Gypsum to composite
- On all gypsum materials
- For heat curing and self (cold) curing acrylics
Important information:
- Applying on a hot model accelerates infiltration and drying of the separating agent.
- If applying a second coat the first layer of separating agent should not be completely dried before the second layer is applied. If so, this can result in white discolouration on the acrylic surface. The second coat should only be a light application and be rinsed liked the first coat.
- Never empty remaining separating agent back into the original container or immerse the used brush in the bottle. This results in contamination and consequently degradation of the separating solution.
DO NOT STORE IN DIRECT SUNLIGHT OR HOT AREA
Must be stored at no more than 25° in dark area (Heat Sensitive). Product may lose red colour due to light.
Use with in 6 months
**** Please be aware Separating Solutions are affected by heat exposure or UV exposure which will cause them to loose their properties. Product must be stored in a cool dark place and should be decantered into small bottle to use in the working area. If the solution has gone watery (no longer slimy or slightly thick) then it will no longer work as the natural alginate material has broken down due to elements.
Related Products
Kulzer Palaseal Single - 2 x 15ml - 66077049
Palaseal is a light‐curing, transparent sealing resin that bonds to any denture materials, temporary..
Lab Pan Job Box With Job Card Clip - Single - 1pc
Available in: Blue, Red, Green, Yellow and White Lab Work Pans are a great way to organize your l..
Kulzer Aislar Separating Solution - 2 x 1L Bottles - 64708058
Kulzer Aislar Separating Solution - 2 x 1L Bottles - 64708058 Separating solution is painted on t..
Durodent Model Seal Separating Solution 5L
Durodent Model Seal Separating Solution IMROVED FORMULA - Increased stability Separa..
Orthodontic Model Rubber Model Base Formers - Two Size Options
Orthodontic Rubber Model Base Formers - Single Pieces MBF-G2.1-LU ..
Ernst Hinrich HinriScan Spray PLUS - 200ml (DG)
Ernst Hinrich Scan Spray PLUS – CAD CAM High Grade Extra-Fine atomiser for ultra fine spray..
Kemdent ClarDent EXTRA Large Rubber Model Base Former - Red - UPPER or LOWER - 1pc
Orthodontic Model Base Formers - Rubber Size: Extra Large For quick clean construction of models..
Scantist 3D Vanishing Scan Spray 1 x 200ml (DG)
Scantist 3D Vanishing Scan Spray 200ml Extraoral scan-spray for the dental industry For opt..
Kulzer Palaseal Single - 2 x 15ml - 66077049 - DAMAGED STOCK CLEARANCE
Kulzer Palaseal Single - 2 x 15ml - 66077049 - DAMAGED STOCK CLEARANCE VERY SMALL AMOUNT OF PRODU..